JBL SVA2100顶级落地箱 （
已出，封贴）1;数量：1
2：价格：11800元
3：成色：8.5成
4：物品缺陷及改动：无
5：三包或保修期：无
6：卖家所在地：广东汕头
7：卖家联系方式：13169035785
8：淘宝连接：http://store.taobao.com/shop/view_shop.htm?asker=wangwang&shop_nick=asa87252229：运输方式及运费；货运This is my collection of JBL SVA series speakers. I have two pairs, one pair of SVA-1800's and one pair of SVA-2100's and I like the design for a number of reasons as described below.
Specifications & Design
As you can see, these are big heavy speakers and they have a hell of a punch to the sound with the 1800's having a pair of parallel 8 inch bass/mid drivers and the 2100's a pair of 10 inch bass/mid drivers in a bass reflex enclosure with the ports at the back and a horn loaded dome tweeter. The pictures here are of 2100's but the 1800's look just the same except slightly smaller of course. So this is essentially a 2-way moving coil bass-reflex design where the two large bass/mid drivers are wired in parallel and constitute a single logical driver. This configuration has the advantage that there is only one crossover point (1600Hz for the 1800's and just 1200Hz for the 1800's) between the bass/mid range & the treble and so gives a smoother transition across the range than a 3 or 4-way system can achieve. With the two bass/mid drivers being mounted above & below the tweeter, all the sound appears to emanate from a single point which gives razor sharp stereo imaging, and it's a cleaver design feature. The 2100's also have two bass reflex ports in the back panel whereas the 1800's have just one. Some people incorrectly think that the sound will not be right if the bass reflex ports are on the back of the speaker cabinet like in the SVA's instead of the front. In fact, the wave length of the sound that comes out of the port at the point of cabinet resonance (about 35 Hz or so and the only time the sound from there has any impact at all) is so long, that the direction and phase of the sound makes no audible difference at all! The science of enclosure and port design is referred to as a Speaker Alignment and has been defined by Thiele & Small. In some cases the number and length of ports required to properly align a given enclosure make it impractical for the ports to be mounted on the same side of the cabinet as the speakers as there would either not be enough room or the baffle would be weakened by all the holes, especially with a design like this where the tweeter actually uses more baffle space than the woofer! Having said all that, in most cases it is done by speaker manufacturers to give a funky look and add mystery to the design! Some KEF systems even have the reflex port in the top!
The horn loading of the tweeter focuses and increases the level of treble enabling the single tweeter to keep up with the power handling of the pair of bass/mid drivers. This gives the speakers an aggressive sound and the contour can be adjusted slightly on the crossover with a screw on the back as shown below:
In general the 1800's & 2100's have a similar sound with the low end response of the 2100's being slightly deeper due to their extra size. Even so, the 1800's are still massive weighing in at 75lbs each with thumping bass and are bigger than most people would accept in their lining room in a normal stereo system. When setup in a stereo setting with the tweeter horns pointing right at you, the tweeter contour control needs to be set to the 0dB position for the treble end to be comparable in level to other speakers without such a control unless you like a sharp edge to your sound.
I bought the 1800's new in 1997 at a cost of about $1200 to use as a pair for the single center channel in my surround sound system at the time and I used to have them standing on each side of the projector screen. They sure made a fantastic impact on film material as a center system. Their vast power not to mention range made any other single center channel speaker somewhat of a joke by comparison. Film soundtracks are quite different from music from a CD for example. The speakers need to be able to reproduce quiet delicate uncolored speech to vast explosions from one second to the next. While somewhat brash sounding for CD music, these are my favorite speakers for DVD & Laserdisc film soundtracks.
Current Usage
When I setup the home theatre system at Chester River, as I still liked the sound of the SVA-1800's for film material, I decided to use the 1800's as the rear surround speakers to replace the smaller ones I had there and try to acquire a pair of used 2100's to use as the front center system. Luckily I came across a pair on eBay that were available in Los Angeles and I paid about $850 for them plus shipping. At Chester River the setup required that we have an unobstructed view of the bay, so the 2100's lay on their sides each side of the subwoofer. I removed the feet so that the bottom of each speaker could sit close to the side of the subwoofer. For a start I tried tilting them to face upward a bit by placing some wedge shaped blocks under each side so that the tweeter horns were facing the listening position. Of course they sounded fantastic because of their increased size over the 1800's but somehow I didn't like to look of them tilting up like that so I tried them with the sides flat on the floor. This looked much better and meant that I could put the Technics SE-A5 power amp for each side, on top of each speaker. As some of the sound was now pointing at my feet although the domes of the tweeters are still visible from the listening position, I set the tweeter contour control to the +2dB setting and that was just enough to now make the sound the same as it was before with the speakers tilted. With 240 watts from each Technics SE-A5 power amp driving each speaker I guess I'd better keep my slippers on for safety!
The inputs of the two channels of each Technics SE-A5 power amp are all connected to the single center channel 5.1 output of the Marantz AV-9000 processor. Then the speakers are bi-wired from each channel of each amp as shown below, so the speakers are both bi-wired and bi-ampped.
The SVA-1800's now used as a rear surround pair are mounted on 3 foot high stands at the rear of the room facing sideways towards the listening position. This gets the tweeters at just the right ear level. Of course, such massive speakers were never intended to be used on stands and if you set them up like that at the front of the room in a stereo pair, they look totally over powering! But in the rear corner of the room, they hide away there without too much problem and nobody has ever pointed them out there. The rear speakers are driven by my Onkyo M-504 power amplifier which at 165 watts per channel makes a awesome rear surround system!
Photos & Reference
JBL SVA2100型号角式音箱
★ 世界品牌JBL SVA 2100號角式喇叭 ★
http://www.adrian-kingston.com/JBL.htm★ 10-"Symmetrical Vertical Array ★ Hr\orn System
★雙10”低音單體 ★JBL專利之Bi-Rodiol號角設計 ★承受功率：300W
★頻率響應：40Hz~18kHz(+/-2dB) ★靈敏度：93dB ★輸入阻抗：8Ω
★具防磁設計 ★材質：黑色橡木音箱及號角核桃木紋飾板
★ 可Bi-Wire連接 ★ 獨特可調適前腳設計
★ 總重量：一對共計約96公斤
★ 喇叭尺寸（HxWxD） 1092 x 368 x 514mm
原边，无修模，状态完好。附件
DSCN0942.JPG (117.89 KB) 2011-5-17 19:22
DSCN0946.JPG (93.75 KB) 2011-5-17 19:22
DSCN0954.JPG (101.28 KB) 2011-5-17 19:22
DSCN0959.JPG (112.34 KB) 2011-5-17 19:22
DSCN0962.JPG (53.26 KB) 2011-5-17 19:22
DSCN0965.JPG (112.48 KB) 2011-5-17 19:22
